Whether you’re a professional mechanic or not, it can be incredibly difficult to fix the type of exhaust pipe that your vehicle has. Many different exhaust pipe types exist, and those can be incredibly difficult to fix. In this article, you’ll learn about how to fix exhaust pipe without welding.
The exhaust system is designed to deal with the air pollution emitted from your car’s engine. It becomes clogged in two ways. Firstly, a clog can form, restricting exhaust gasses from flowing properly.
Secondly, the rubber lining of the system can get heavily damaged and can no longer offer the ideal protection to the engine. If your exhaust pipe was recently damaged in an accident, you must take action.
You might need to purchase a new exhaust pipe if your current one severely corrodes. However, if the leak is modest, there is no need to spend money that is not necessary. You can repair any leak using materials that are readily available locally without using a welder.
How to Fix Exhaust Pipe Without Welding
If the exhaust pipe has a crack or exhaust leak, you first need to make sure that the crack or leak is not too large. You should use a hammer or a screwdriver to push the crack back into place. You don’t want the crack to spread too much or for the crack to become too big.
After the crack is back in place, you can start using heat to seal it. It should make the repair effective. Next, you should make sure that the pipe is not clogged. You should use a drill to unblock the pipe if it is clogged. Make sure that you do this as soon as possible.
Clogged pipes emit toxic fumes, which could damage your lungs. Here are a few methods to fix exhaust pipes without welding:
Exhaust Clamps
There is nothing firmly attached to which the exhaust pipe could be secured. If you have a clamp, use it to tighten it over the exhaust pipe’s weakly held end; perhaps that will solve the issue.
The exhaust pipe should be tightened with a screwdriver if you don’t have a clamp. If you don’t have one of those, you can also use the palm of your hand.
Crimp Bending
Take a pair of pliers and pull apart one side of the exhaust pipe if clamping does not solve your issue. The exhaust pipe should then be bent level and straight while being held by the open side.
If you were unable to separate one side of your exhaust pipe, try again. Holding the first side, bend it until it is straight and level. Use tape or electrical tape to hold the exhaust pipe together if you are unable to make it stay in its modified shape.
Use Acetone to Clean the Surface
Pour some acetone over the damaged surface of your exhaust pipe if you have any lying around. If acetone is unavailable, get a lighter and burn off any extra oil or grime on your exhaust pipe. After that, use a towel to polish its surface until it has a lovely shine.
Put the Thread Locker on it.
Cover any exposed exhaust pipe ends with a disc brake thread locker, so they stay together. This glue is intended to firmly bind objects together when they are subjected to pressure or heat. If you have not already done so, keep in mind to clean the surface first.
Plunger Gasket
If no clamps or screwdrivers are present, grab the plunger gasket. Put it where you wish to fix it on your exhaust pipe, then pound one side of it flush against the other.
If you don’t have a plunger gasket, hold the two opposing ends together with a screwdriver or pliers if you’ve used them before until they lock into place.
Use some tape to patch up the crack.
If the two halves of the exhaust pipe are not in alignment. You can use duct tape to put the two halves of the exhaust pipe back together. You can also use caulking material to seal up the crack.
Exhaust Putty
It’s time to try to exhaust putty if none of the earlier methods have worked. Spread some of the epoxy-like stuff on your split end or against either side of your weakly clamped end until it is completely coated. If it doesn’t work, acquire some super glue and dab a tiny bit on each side of the split end. Till the glue has dried, firmly press the pieces together and keep them there.
Get a Flex Pipe
The Flex Pipe is an alternative to duct tape. It is an elastic material that can be stretched to fit around the exhaust pipe. Once it is in place, it will hold the two ends of the exhaust pipe together. It makes it easier to make sure that the two pieces are aligned correctly. Ensure that the pipe clamped onto the exhaust pipe is properly clamped so that it is held tightly in place.
Use a Mig Welder to Weld It
If you are skilled at welding, pull out your MIG welder and join the fractured pieces. Heat the metal on one side of the split exhaust pipe until it is red hot, then firmly press down on the opposing side to unite them.
Apply Silicone Coating on It
Grab some silicone and use a paintbrush to spread it thickly on the split pipe. Before operating your exhaust system once more with a car or other gasoline-powered vehicle, let this solution completely dry.
Tips and Suggestions
Here are some suggestions for fixing exhaust pipes without welding:
- Having the appropriate tools will help you save time and effort.
- Before doing anything, use a wire brush or sandpaper to wipe up your exhaust pipe and remove any rust or peeling paint.
- Be ready for the potential that you’ll need to buy fresh items to complete your project.
- Make sure the pipe is completely covered with steel wool.
- Wrap as much as you can because it will make your bond stronger.
Final Thoughts
We hope you enjoyed the blog post on how to fix exhaust pipe without welding. Sometimes, it’s best just to replace the pipe rather than try to tin the crevices with a soldering iron. It can be frustrating to have to remove the pipe and scrape the crevice, but if you can find one in good condition, this could save you some time and be more cost-effective than hiring a welder. If you’re having trouble with your exhaust pipe, don’t worry! We have provided a solution here to help you repair your broken pipe! Thank you for reading!